Garage floors
Garage Floor Coatings in Lewisville, TX
A real Lewisville project, how we prepare and coat a garage floor, and what a garage this size costs.
Drag the slider to compare a garage floor before and after. This is an example of Epoxy Panda's work from another job, not the Lewisville project described below.
Epoxy Panda installs garage floor coatings in Lewisville, Texas. One completed Lewisville project was a two-car, 450 sq. ft. garage where we diamond-ground the concrete, repaired surface defects and installed a full-flake system with a protective topcoat.
A Lewisville Garage We Coated
- Garage
- Two-car garage
- Size
- About 450 sq. ft.
- Concrete before
- Several areas of discoloration and minor cracking near one side of the slab.
- Preparation
- Diamond-ground the entire floor, repaired the cracks and surface imperfections and prepared the concrete for the coating system.
- System
- Full decorative flake broadcast with a protective topcoat.
- Installation time
- One day
This Lewisville homeowner had recently finished painting and reorganizing the garage but felt the old concrete floor made the project look incomplete. The garage measured about 450 square feet.
In one day, the garage went from a partially updated utility space to a finished part of the home.
How Do We Prepare and Coat Garage Floors?
- Inspect the concrete for existing coatings, cracks, pitting, contamination and moisture.
- Mechanically prepare the concrete with diamond grinding, which removes weak material and creates the profile the coating needs to bond.
- Repair appropriate cracks, pits and surface defects.
- Apply the resin base coat. Epoxy Panda may use epoxy, polyurea, polyaspartic or a hybrid, depending on the system.
- Broadcast decorative flake across the wet base coat when installing a flake system.
- Scrape and remove the excess flake.
- Apply the protective topcoat. Epoxy Panda’s standard topcoat is a polyaspartic clear.
Learn more about garage floor coatings, flake floor systems and concrete grinding & preparation.
How Much Does a Garage Floor Coating Cost in Lewisville?
Epoxy Panda’s planning range for the approximately 450 sq. ft. Lewisville garage on this page is $3,150–$3,600, for a full-flake system with mechanical preparation included. This is a planning estimate. After a free in-person consultation, Epoxy Panda provides a written estimate that confirms the actual price.
Price depends on square footage, concrete condition, existing coating removal, significant repairs, steps, vertical surfaces, specialty traction and system selection. See Epoxy Panda’s garage floor coating pricing or use the planning calculator with your own square footage.
What Should You Know Before Coating a Garage Floor?
- A coated garage floor is generally easier to sweep, vacuum and mop than unfinished concrete.
- Decorative flake can help visually disguise minor dirt, small imperfections and everyday wear better than a uniform solid-color surface.
- Garages with strong direct sunlight at an open door need a system selected with UV exposure in mind.
- A coating does not stop concrete from moving, so a repaired crack can sometimes become visible again.
- Glossy finishes can be slippery when wet, and texture can be added where traction matters.
Lewisville Garage Floor Coating FAQs
How much does a garage floor coating cost in Lewisville?
For the approximately 450 sq. ft. Lewisville garage on this page, the planning range is $3,150–$3,600. The final price depends on the concrete, finish, repairs and other project-specific conditions.
How long does a garage floor coating take in Lewisville?
The 450 sq. ft. Lewisville garage featured on this page was completed in one day. Installation time for other garages depends on the concrete condition, preparation requirements and coating system.
Do you grind the concrete before installing a garage floor coating?
Yes. Epoxy Panda uses mechanical preparation such as diamond grinding as part of its garage floor coating process so the coating is installed over properly prepared concrete.
How soon can I walk on or park on my garage floor after coating in Lewisville?
For most Epoxy Panda systems, light foot traffic is typically possible in approximately 12–24 hours, with vehicle traffic in approximately 24–72 hours. Exact timing depends on coating chemistry, temperature, humidity and project conditions.
What is a full-flake garage floor system?
A full-flake system uses decorative vinyl flake broadcast across the wet base coat before the floor is sealed with a protective clear topcoat. A standard Epoxy Panda full-flake garage system includes prepared concrete, a resin base coat, a full decorative flake broadcast and a protective clear topcoat.
What can increase garage floor coating cost in Lewisville?
Existing coating removal, significant concrete repair, steps, vertical surfaces, specialty traction and other project-specific conditions can increase the price. The written estimate confirms the actual price for the garage.
Garage Floor Coatings Near Lewisville
Get a Free Garage Floor Estimate
Tell us about your Lewisville garage. We text to confirm, ask for a few photos, then visit for a free in-person consultation and a written estimate.